Infiltrator Quick 4 Low Profile

Through its four central structural columns, the Quick4 Plus, Standard Low Profile, offers maximum strength. This chamber can fit in a 36 inch trench. This chamber is smaller in height than Infiltrator Standard model chambers. It can be installed easily. It is similar to the Quick4, and offers advanced contouring capabilities with its Contour Swivel Connection, allowing turns of up to 10deg right or left.

This chamber is designed to be strong in trench and bed applications. Its unique design features include a low profile design that makes it ideal for applications requiring shallow placement. The Quick4 Equalizer 24-LP Chamber is perfect for straight and curved systems. Easy installation is made possible by the low profile cap.

Product Details

  • Installation is quick and easy with the latch mechanism
  • The 4ft lengths of the chambers are simple to install and handle.
  • Supports wheel loads up to 16000 lbs/axle and 12 inches of cover
  • This chamber is ideal for applications that require a low profile.
  • Imported fill required for fill and cap systems is reduced
  • Superior strength is provided by four central structural columns
  • Advanced contouring connection

Benefits:

  • This chamber is ideal for applications that require a low profile.
  • Imported fill required for fill and cap systems is reduced
  • Superior strength is provided by four central structural columns
  • Advanced contouring connections
  • Installation is quick and easy with the latch mechanism
  • Easy to install and handle chambers measuring four feet long
  • Supports wheel loads up to 16,000 lbs/axle and 12″ of cover

Specifications:

Size

34″W x 53 1/2″L x 8”H

(864 mm x 1346 mm x 203 mm)

Effective Length

48″ (1219 mm)

Louver Height

6.3″ (160 mm)

Storage Capacity

32 gal (121 L)

Invert Height

3.3″ (84 mm), 9.6″ (244 mm)

Features

  • Compact nesting allows for more trench length at the same height as the stack height.
  • Four-foot chambers can be easily installed and handled.
  • 17 gal storage capacity
  • 6 in H louver
  • 48 in L effective
  • 8.8 in chamber height allows for shallow installations with 4in of cover
  • Advanced contouring connections can swivel up 15 degrees right or left
  • Reinforced Ribs offer greater structural strength and endurance

FAQ’s

In Which Types Of Systems Can Infiltrator Chambers Be Installed?

Infiltrator chambers are suitable for almost all septic leach fields. Infiltrator chambers are able to be used wherever stone and pipe can fit. These include trench, bed, or elevated mound installations. Infiltrator chambers provide superior treatment capabilities in pressure dosing, level distribution, serial distribution, evapotranspiration, and sand filter applications.Infiltrator chambers have a patented MicroLeaching(tm) louver design that corresponds to the angle of the soil. This allows effluent to be ejected from the sidewall, while keeping soil out.

What Is The Maximum Size Of The Leach Field That Can Be Reduced When I Install Infiltrator Chambers?

Each local health department determines the system size. Health departments typically approve sizing cuts of 25 to 50% when Infiltrator rooms are specified. For details, check your local health codes. This provides the chambers with a firm footing that does not affect the infiltration rate.

Sidewall louvers of Infiltrator MicroLeaching are made to keep soil out. Therefore, a filter fabric is not required

.

What Is Infiltrator Water Technologies’ Minimum And Maximum System Coverage?

Infiltrator Water Technologies recommends that the chambers have a minimum of 12 inches of covered compacted material. The maximum allowable cover for chambers in trench systems is 96 inches. Maximum cover for bed systems is 48 inches. Minimum cover can be reduced to six inches if the drainfield is not in use. When installing a 6-inch system, be careful with your equipment. Infiltrator Water Technologies offers a line for Shallow Cover (SC), Chambers. These allow for six inches of coverage with an H-10 equivalent loading speed, but these are limited to certain markets. Check with your local health codes to determine specific requirements. Each chamber has a knock-out that is usually used for an inspection port. A splash plate must be placed under the inlet to allow for inspection. Be careful when backfilling to avoid causing damage to the inlet pipe.

Leave a Reply

Your email address will not be published. Required fields are marked *